What is 42CrMo4 Alloy Steel for Hydraulic Cylinders

42CrMo4 alloy steel (DIN 1.7225) is a medium carbon chromium‑molybdenum alloy steel, equivalent to AISI 4140 and JIS SCM440. In hydraulic cylinder manufacturing, 42CrMo4 alloy steel is our preferred material for high‑stress piston rods and thick‑wall honed tubes when standard carbon steel cannot handle heavy loads.

Carbon delivers basic strength. Chromium improves hardness and wear resistance. Molybdenum prevents brittleness after heat treatment. This unique mix gives 42CrMo4 alloy steel better overall performance than CK45 / 1045 carbon steel.

Key Properties of 42CrMo4 Alloy Steel

42CrMo4 alloy steel reaches its best mechanical performance after quenched and tempered (QT) heat treatment.

  • Tensile strength: 900–1100 MPa after QT
  • Great hardenability. Large‑diameter bars get uniform hardness from surface to core
  • Excellent fatigue resistance for repeated extend‑retract cycles
  • Good toughness to absorb shock loads and sudden pressure spikes
  • Compatible with induction hardening and hard chrome plating for surface protection

For hydraulic applications, buyers often ask about the hardness range of 42CrMo4 alloy steel. Normally, finished QT 42CrMo4 alloy steel stays between 28 HRC and 34 HRC. This range balances hardness and impact toughness. If hardness is too high, the steel becomes brittle and cracks under impact. If hardness is too low, the rod will bend easily under heavy side force.

42CrMo4 alloy steel also has clear limits. It costs more than ordinary carbon steel. Its heat treatment process needs strict control. Welding 42CrMo4 alloy steel requires preheating and slow cooling. Improper welding will create internal cracks and shorten cylinder service life.

Surface finish tolerance for 42CrMo4 alloy steel parts

For hydraulic use, raw 42CrMo4 alloy steel alone is not enough. Precision machining and surface finishing decide sealing performance. For 42CrMo4 alloy steel piston rods, we control straightness, roundness and surface roughness before chrome plating. Any tiny scratch or out‑of‑tolerance spot will quickly wear out the oil seal and cause leakage. For 42CrMo4 alloy steel honed tubes, consistent honing quality is critical. Even if the steel grade is correct, poor honing marks will damage seals and raise friction heat during continuous cylinder operation. This is why we inspect every finished 42CrMo4 alloy steel component before assembly.

Common Uses of 42CrMo4 Alloy Steel in Hydraulic Cylinders

42CrMo4 alloy steel piston rod

This is the most popular application. We machine raw 42CrMo4 alloy steel bars first. Most rods go through quenching and tempering. Then we add 20–30 μm hard chrome plating. For extreme heavy‑duty orders, we add induction hardening to further lift surface hardness.

These piston rods fit mining equipment, construction breakers, offshore machinery and cylinders working above 250 bar. 42CrMo4 alloy steel greatly lowers the risk of rod bending or fracture under side load and impact. We follow ISO f7 tolerance to keep stable sealing.

42CrMo4 alloy steel honed tube

ST52.3 / E355 works well for most general‑purpose cylinders. But for high‑pressure custom hydraulic cylinders, we choose seamless 42CrMo4 alloy steel tube. After precision honing, the inner bore reaches Ra 0.2–0.4 μm. The smooth surface protects seals and reduces internal friction. Important tip: weld end caps before honing, and follow dedicated welding procedures for 42CrMo4 alloy steel.

42CrMo4 alloy steel honed tube

42CrMo4 Alloy Steel vs CK45: Quick Selection Guide

  • CK45: Medium pressure, stable load, standard projects, cost saving
  • 42CrMo4 alloy steel: High pressure, shock load, frequent cycles, long service life

You do not have to select 42CrMo4 alloy steel for every cylinder. Over-spec material only raises your cost without extra practical value.

Our Supply of 42CrMo4 Alloy Steel at ANBAO

We source certified 42CrMo4 alloy steel raw material. Every batch comes with an MTR material test report. We supply QT bars, chrome‑plated piston rods, honed tubes and complete custom hydraulic cylinders made from 42CrMo4 alloy steel.

Send us your bore, stroke, rod diameter, working pressure and load condition. Our engineering team will check if 42CrMo4 alloy steel matches your project, or recommend a more economical steel grade.

Authoritative External References

  1. Thyssenkrupp Steel: 42CrMo4 material datasheet
  2. ISO heat treatable steel standard EN ISO 683‑2 
  3. Hydraulics Online material guide for hydraulic cylinder components

Table of Contents

Contact Us

Please feel free to contact us if you have any questions or product requirements.

Need a Custom Hydraulic Solution?

Whether you have standard or customized requirements, please provide your details. We will offer professional advice and highly competitive quotes. Trusted by B2B clients worldwide.